Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and flaps
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box of airinflow
11.8. Cowl
11.9. Doors
11:10. Trunk lid
11.10.1. Replacement of torsions of a trunk lid
11.10.2. Removal and installation of a trunk lid
11.10.3. Replacement of the lock, latch and switch of the lock of a trunk lid
11.10.4. Removal and installation of the drive of the lock of a trunk lid
11.10.5. Removal and installation of a decorative overlay of a trunk lid
11:11. Cover of the hatch of a bulk pipe of the fuel tank
11:12. Seats
11:13. Removal and installation of facing of a tunnel of a floor
11:14. System of passive safety (SRS)
11:15. Rear-view mirrors
11:16. Dashboard
11:17. Heater and conditioner
11:18. Fittings of salon
11:19. Removal and installation of facings of salon
11:20. Removal and installation of facings of a luggage carrier
11:21. Screen wiper of a wind window
11:22. Replacement of a motionless glazing of a body
11:23. Removal and installation of the shelf of fastening of the rechargeable battery
11:24. Care of a body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








11-10-3-zamena-zamka-zashhelki-i-vyklyuchatelya-zamka-kryshki-bagazhnika.html

11.10.3. Replacement of the lock, latch and switch of the lock of a trunk lid

It will be required to you: a key "on 10" (the face head is more convenient), the screw-driver with a flat edge.
1. For removal of the lock of a trunk lid remove facing of the panel of a back (see. "Removal and installation of facings of a luggage carrier").
2. From within a luggage carrier turn out two bolts of fastening of the lock to the amplifier of the panel of a back …
3. … also remove the lock outside through a window in the panel.
4. Bring a lock drive cable tip out of a lever cut …
5. … a cable cover tip from a lock case cut also remove the lock.
6. Put the lock as it should be, the return to removal.
7. If the lock indistinctly locks a trunk lid or, on the contrary, unlocks with difficulty, adjust lock drive cable cover length for what through a window in the amplifier of the panel of a back take a cover tip from a cut of the case of the lock and rearrange it in other situation. At indistinct locking of the lock move a tip in the direction of the lock lever, at the complicated unlocking — in an opposite direction.
8. Establish facing of the panel of a back (see. "Removal and installation of facings of a luggage carrier").
9. If the zakhlopyvaniye of a trunk lid is followed by blow of a latch about the lock lever, adjust position of the lock for what from within a luggage carrier weaken two bolts of fastening of the lock …
10. … and, moving the lock in the cross direction, achieve an unaccented zakhlopyvaniye. Then tighten bolts of fastening of the lock.
11. For removal of a latch of the lock of a luggage carrier from within a trunk lid unfasten a clamp of draft of the switch of the lock …
12. … also disconnect draft from the switch lever.
13. Disconnect a wire from the trailer switch of a latch.
14. Turn out two screws of fastening of a latch to the amplifier of a trunk lid …

    
NOTE
The right screw of fastening of a latch at the same time fixed also a "mass" wire. Do not forget to establish it into place at the return installation of a latch.

15. … also remove a latch.
16. If the latch was removed for replacement, disconnect draft of the external drive from its lever, having unfastened a draft clamp, and rearrange draft on a new latch.
17. Establish a latch of the lock of a luggage carrier and all removed details as it should be, the return to removal.
18. For removal of the switch of the lock of a luggage carrier disconnect from its lever thirst for a lock latch (see subitems 11 and 12).
19. Turn off two nuts of fastening of the switch to the external panel of a trunk lid …
20. … also remove the switch.
21. For replacement of the cylinder or a spring of the switch remove a lock washer from a cylinder shaft, having hooked it the screw-driver.
22. Insert a key into the switch cylinder …
23. … remove from a shaft the lever 1 and if necessary a spring 2 from the switch case.
24. Take the cylinder from the switch case.
25. Collect and install the switch of the lock of a trunk lid and all removed details as it should be, the return to removal.

    
NOTE
Before assembly of the switch grease its cylinder with silicone lubricant.

"previous page
11.10.2. Removal and installation of a trunk lid
following page"
11.10.4. Removal and installation of the drive of the lock of a trunk lid