Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and flaps
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box of airinflow
11.8. Cowl
11.9. Doors
11:10. Trunk lid
11:11. Cover of the hatch of a bulk pipe of the fuel tank
11.11.1. Removal and installation of a cover of the hatch of a bulk mouth of the fuel tank
11.11.2. Removal and installation of the lock of a cover of the hatch of a bulk pipe of the fuel tank and its drive
11:12. Seats
11:13. Removal and installation of facing of a tunnel of a floor
11:14. System of passive safety (SRS)
11:15. Rear-view mirrors
11:16. Dashboard
11:17. Heater and conditioner
11:18. Fittings of salon
11:19. Removal and installation of facings of salon
11:20. Removal and installation of facings of a luggage carrier
11:21. Screen wiper of a wind window
11:22. Replacement of a motionless glazing of a body
11:23. Removal and installation of the shelf of fastening of the rechargeable battery
11:24. Care of a body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








11-11-2-snyatie-i-ustanovka-zamka-kryshki-lyuka-nalivnojj-truby.html

11.11.2. Removal and installation of the lock of a cover of the hatch of a bulk pipe of the fuel tank and its drive

It will be required to you: all tools necessary for removal of back facing of the left threshold of a floor and facings of a luggage carrier, and also a face head "on 10".
1. Remove forward and back facings of the left threshold of a floor (see. "Removal and installation of facings of salon").
2. Remove facings of an arch of the left back wheel, both back lamps and the panel of a back (see. "Removal and installation of facings of a luggage carrier").
3. Turn out through a window in a floor rug a bolt of fastening of the block of handles.
4. Unbend edge of a rug and take from under a rug the block of handles together with cables of drives, having stretched the block through a window in a floor cross-piece.
5. Take out a tip of a cover of a cable of the drive of the lock of a cover of the hatch of a bulk pipe of the fuel tank from a cut of an arm of the block of levers and, having taken out a cable tip from a lever cut, disconnect a cable.

NOTE
If necessary similarly disconnect from the block of handles a luggage carrier lock drive cable (with a yellow tip) and remove the block of handles.

6. Take a cable cover from holders on the left threshold of a floor …
7. … on the left sidewall in a luggage carrier …
8. … and on the amplifier of the panel of a back.
9. Open a cover of the hatch of a bulk mouth of the fuel tank and take from a nest in the right back wing the lock of a cover of the hatch of a bulk pipe of the fuel tank, overcoming resistance of its clamps.
10. Disconnect a cable tip from the lock lever …
11. … separate the case of the lock and a tip of a cover of a cable and remove the lock.
12. Remove a drive cable, taking both of its ends in a luggage carrier.
13. Examine a lock sealant. Replace strongly hardened or damaged sealant.
14. Install as it should be, the return to removal, the lock of a cover of the hatch of a bulk pipe of the fuel tank and its drive, and also all removed details.

"previous page
11.11.1. Removal and installation of a cover of the hatch of a bulk mouth of the fuel tank
following page"
11:12. Seats