Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and flaps
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box of airinflow
11.8. Cowl
11.9. Doors
11:10. Trunk lid
11:11. Cover of the hatch of a bulk pipe of the fuel tank
11:12. Seats
11.12.1. Removal and installation of a front seat
11.12.2. Removal and installation of a head restraint of a front seat
11.12.3. Removal and installation of a back seat
11:13. Removal and installation of facing of a tunnel of a floor
11:14. System of passive safety (SRS)
11:15. Rear-view mirrors
11:16. Dashboard
11:17. Heater and conditioner
11:18. Fittings of salon
11:19. Removal and installation of facings of salon
11:20. Removal and installation of facings of a luggage carrier
11:21. Screen wiper of a wind window
11:22. Replacement of a motionless glazing of a body
11:23. Removal and installation of the shelf of fastening of the rechargeable battery
11:24. Care of a body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








11-12-3-snyatie-i-ustanovka-zadnego-sidenya.html

11.12.3. Removal and installation of a back seat

The pillow of a back seat integral can be also removed entirely. The back of a back seat consists of two parts, each of which can be removed separately. Below removal of the right part of a back is shown, the left part is removed similarly.
It will be required to you: a key "on 12" (it is more convenient to use a face head), a stripper for removal of percussion caps or the screw-driver with a flat edge.
1. Having raised a forward part of a pillow of a back seat, bring two brackets of its fastening out of openings on a body on the right and at the left.

NOTE
So brackets of fastening of a pillow look …
… and so — openings in a body.


2. Wring out an upholstery in a back part of a pillow on the right and at the left to get access to two bolts of its fastening to a body...
3. … turn out bolts …
4. … also take a pillow of a back seat from interior of the car.
5. Access to bolts of fastening of the right part of a back of a back seat is closed by edge of the upholstery of a luggage carrier attached to a body by three percussion caps. Disconnect edge of an upholstery from a body …
6. … having removed percussion caps a special stripper or having hooked the screw-driver …
7. … turn out two bolts of fastening of the right part of a back to an arm …
8. … shift the right part of a back down and to the left …
9. … to take a back clamp from an opening in a body, and remove the right part of a back of a back seat from the car.
10. In need of replacement of the lock of a back of a back seat screw together the button from draft of the drive of the lock …
11. … turn off two nuts of fastening of the lock to a seat framework …
12. … also remove the lock.
13. For removal of a latch of the lock of a back of a back seat remove back facing of a sidewall (see. "Removal and installation of facings of salon") also turn out two bolts of fastening of a latch to a body.
14. Establish a back seat and all removed details as it should be, the return to removal.

"previous page
11.12.2. Removal and installation of a head restraint of a front seat
following page"
11:13. Removal and installation of facing of a tunnel of a floor