Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and flaps
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box of airinflow
11.8. Cowl
11.9. Doors
11:10. Trunk lid
11:11. Cover of the hatch of a bulk pipe of the fuel tank
11:12. Seats
11:13. Removal and installation of facing of a tunnel of a floor
11:14. System of passive safety (SRS)
11.14.1. Features of a design
11.14.2. Removal and installation of a safety cushion of the driver
11.14.3. Replacement of a forward seat belt
11.14.4. Replacement of a back seat belt
11.14.5. Removal and installation of an electronic control unit additional system of passive safety
11:15. Rear-view mirrors
11:16. Dashboard
11:17. Heater and conditioner
11:18. Fittings of salon
11:19. Removal and installation of facings of salon
11:20. Removal and installation of facings of a luggage carrier
11:21. Screen wiper of a wind window
11:22. Replacement of a motionless glazing of a body
11:23. Removal and installation of the shelf of fastening of the rechargeable battery
11:24. Care of a body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








11-14-2-snyatie-i-ustanovka-podushki-bezopasnosti-voditelya.html

11.14.2. Removal and installation of a safety cushion of the driver

The safety cushion of the driver should be removed at repair of elements of steering and electric equipment of the car. Therefore process of its removal and installation is described in this manual. However in order to avoid getting injured strictly adhere to the recommended sequence of work.
It will be required to you: TORX T50 key, the screw-driver with a flat edge.
1. Disconnect a wire from the minus plug of the rechargeable battery.
    
PREVENTIONS
The attempt of removal of the module of a safety cushion without shutdown of the rechargeable battery can lead to unexpected operation of a pillow.
It is possible to start the following operations on removal of a safety cushion only after the full category of the condenser of the activator. For the category of the condenser it is necessary to wait not less than 15 min. after a wire detachment from the minus plug of the rechargeable battery.
Dismantling of the module of a safety cushion is forbidden.
Falling of the module of a safety cushion and hit on it of water, lubricant or oil is not allowed.
Impact on the module of a safety cushion of temperature above 95 °C is not allowed.

2. Having hooked the screw-driver, remove caps on facing of a steering wheel at the left …
3. … and on the right.
4. Turn out screws of fastening of a safety cushion to a nave of a steering wheel at the left …
5. … and on the right.
6. Accurately raise the safety cushion module …
7. … take away it from a nave of a steering wheel, having pressed a clamp, disconnect a block of a wire of switches of sound signals …
8. … unfasten a clamp of a block of a plait of wires of a safety cushion …
9. … disconnect a block of wires from the pillow module …
10. … also remove the safety cushion module.
11. Establish a safety cushion as it should be, the return to removal.

"previous page
11.14.1. Features of a design
following page"
11.14.3. Replacement of a forward seat belt