Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and flaps
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box of airinflow
11.8. Cowl
11.9. Doors
11:10. Trunk lid
11:11. Cover of the hatch of a bulk pipe of the fuel tank
11:12. Seats
11:13. Removal and installation of facing of a tunnel of a floor
11:14. System of passive safety (SRS)
11.14.1. Features of a design
11.14.2. Removal and installation of a safety cushion of the driver
11.14.3. Replacement of a forward seat belt
11.14.4. Replacement of a back seat belt
11.14.5. Removal and installation of an electronic control unit additional system of passive safety
11:15. Rear-view mirrors
11:16. Dashboard
11:17. Heater and conditioner
11:18. Fittings of salon
11:19. Removal and installation of facings of salon
11:20. Removal and installation of facings of a luggage carrier
11:21. Screen wiper of a wind window
11:22. Replacement of a motionless glazing of a body
11:23. Removal and installation of the shelf of fastening of the rechargeable battery
11:24. Care of a body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








11-14-3-zamena-perednego-remnya-bezopasnosti.html

11.14.3. Replacement of a forward seat belt

NOTE
Replacement of forward seat belts is shown on the example of a seat belt of the driver. The seat belt of the forward passenger is replaced similarly.

It will be required to you: TORX T30 keys, "on 17", the screw-driver with a crosswise edge.
1. If seat belts are equipped by prednatyazhitel, disconnect a wire from the minus plug of the rechargeable battery.

PREVENTIONS
After a wire detachment from the minus plug of the rechargeable battery it is necessary to wait not less than 10 min. and only after that it is possible to start removal of the seat belt equipped with a prednatyazhitel.
Dismantling of prednatyazhitel of belts is forbidden.
Falling of coils of belts with prednatyazhitel and hit in them of water and oil is not allowed.
Influence on prednatyazhitel of belts of temperature above 95 °C is not allowed.

2. Remove the lower part of facing of the central rack (see. "Removal and installation of facings of salon").

    
NOTE
The seat of the driver is for descriptive reasons removed.

3. Turn out two screws of fastening of a guide of a belt to the central rack.
4. Remove a decorative cap from the lower bolt of fastening of a belt …
5. … also turn out a bolt.

    
PREVENTION
On bolts of fastening of a belt washers and remote plugs are established, do not lose them.

6. Cast away a decorative overlay of a buckle …
7. … also turn out a bolt of the top fastening of a belt.
8. Turn out the screw of fastening of the inertial coil …
9. … also take the coil from a body rack.
10. Before removal of the lock of a forward seat belt separate a block of a plait of wires of an alarm lamp of not fastened seat belt (if you remove a seat belt of the driver).
11. Turn out a bolt of fastening of the lock of a seat belt to a seat …
12. … also remove the lock.
13. Establish a forward seat belt as it should be, the return to removal.

"previous page
11.14.2. Removal and installation of a safety cushion of the driver
following page"
11.14.4. Replacement of a back seat belt