Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and flaps
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box of airinflow
11.8. Cowl
11.8.1. Removal and installation of a cowl
11.8.2. Removal, installation and adjustment of the lock of a cowl and its drive
11.9. Doors
11:10. Trunk lid
11:11. Cover of the hatch of a bulk pipe of the fuel tank
11:12. Seats
11:13. Removal and installation of facing of a tunnel of a floor
11:14. System of passive safety (SRS)
11:15. Rear-view mirrors
11:16. Dashboard
11:17. Heater and conditioner
11:18. Fittings of salon
11:19. Removal and installation of facings of salon
11:20. Removal and installation of facings of a luggage carrier
11:21. Screen wiper of a wind window
11:22. Replacement of a motionless glazing of a body
11:23. Removal and installation of the shelf of fastening of the rechargeable battery
11:24. Care of a body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








11-8-2-snyatie-ustanovka-i-regulirovka-zamka-kapota-i-ego-privoda.html

11.8.2. Removal, installation and adjustment of the lock of a cowl and its drive

It will be required to you: a key "on 10" (the face head is more convenient), the screw-driver with a flat edge.
For removal of the lock of a cowl execute the following.
1. Open a cowl and establish it on an emphasis.
2. Turn out three bolts of fastening of the lock of a cowl to a radiator frame …
3. … take away the lock from a frame, bring a lock drive cable cover tip out of the holder on the lock case …
4. … disconnect a cable tip from the lever of the lock and remove the lock.
5. Put the cowl lock as it should be, the return to removal. Before installation of the lock of a cowl grease its details with jellied lubricant, for example litoly.
6. If after installation the lock is indistinctly locked or hardly opens, adjust its situation. Weaken bolts of fastening of the lock and movement it within oval openings of the case achieve accurate work.

For removal of the drive of the lock of a cowl execute the following.
1. Disconnect a drive cable from the cowl lock (see above subitems 3 and 4 in this subsection).
2. Open the left forward door and, having hooked the screw-driver …
3. … remove the left side cover of the dashboard.

    
NOTE
The side cover of the dashboard needs to be removed for receiving visual access to the place of fastening of the handle of the drive of the lock of a cowl.

4. Turn off two bolts of fastening of the handle of the drive to the dashboard …
5. … bring the handle together with a cable out of the dashboard...
6. … also lower it from under the panel down.
7. Disconnect a cowl lock drive cable tip from the handle lever …
8. … extend a cable cover from an emphasis in the case of the handle and disconnect the handle from a cable, having passed it in an emphasis cut.
9. In a motor compartment take holders of a cable from openings in the left rack …
10. … and in the top cross-piece of a frame of a radiator, and then remove a cable, extending it in podkapotny space.
11. Establish details as it should be, the return to removal.

"previous page
11.8.1. Removal and installation of a cowl
following page"
11.9. Doors