Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
3.1. The engine is not started
3.2. Malfunctions of system of injection of fuel
3.3. Idling was gone
3.4. Interruptions in operation of the engine
3.5. Diagnostics of a condition of the engine on appearance of spark plugs
3.6. The car moves breakthroughs
3.7. The car badly accelerates
3.8. The engine decayed during the movement
3.9. Oil pressure fell
3.10. Engine overheat
3.11. The rechargeable battery is not recharged
3.12. Launch of the engine from external sources of current
3.13. Malfunctions of electric equipment
3.14. There were foreign knocks
3.15. Problems with brakes
3.16. Wheel puncture
4. Maintenance
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








3-2-neispravnosti-sistemy-vpryska-topliva.html

3.2. Malfunctions of system of injection of fuel

On the car the system of the distributed injection of fuel with feedback is applied. Is called distributed injection because fuel is injected into each cylinder by a separate nozzle. The system of injection of fuel allows to reduce toxicity of the fulfilled gases at improvement of road performance of the car.
In this section the malfunctions of system of injection caused by failure of these or those sensors are only briefly described. The order of removal and installation of knots of feed and control systems is given by the engine in the subsections "Power Supply System" and "Control System of the Engine".
In system of injection with feedback establish catalytic converter of the fulfilled gases and the sensor of concentration of oxygen in the fulfilled gases which provides feedback. The sensor traces concentration of oxygen in the fulfilled gases, and the electronic control unit on its signals supports such ratio of air and fuel at which converter works most effectively.

PREVENTIONS
Before removing any knots of system of injection of fuel, disconnect a wire from the minus plug of the rechargeable battery.
Switch-off the rechargeable battery only at the switched-off ignition.
Do not launch the engine if tips of wires on the rechargeable battery are badly tightened.
Never disconnect the rechargeable battery from onboard network of the car at the working engine.
At charging disconnect the rechargeable battery from onboard network of the car as the raised current at charging can put electronic components out of action.
Do not allow heating of the electronic control unit (ECU) above 65 °C in working order and above 80 °C in non-working (for example, in the drying camera). It is necessary to remove EBU from the car if this temperature is exceeded.
Do not disconnect from EBU and do not attach to it sockets of a plait of wires at the included ignition.
Before performance of arc welding on the car disconnect wires from the rechargeable battery and sockets of wires from EBU.
Carry out all voltage measurements the digital voltmeter which internal resistance not less than 10 megohms.
The electronic knots applied in system of injection are calculated on very small tension therefore the electrostatic category can easily damage them. Not to allow damage of EBU by the electrostatic category:
– do not touch with hands plugs EBU or electronic components on its payments;
– during the work with the programmable read-only memory (PROM) of the control unit do not touch chip conclusions.
Work on ethylated gasoline of the engine with converter is not allowed — it will lead to bystry failure of converter and the sensor of concentration of oxygen.
During the work in rainy weather do not allow hit of water on electronic components of system of injection of fuel.

The vast majority of malfunctions of system of injection of fuel is called by failure of its following sensors:
– provisions of a bent shaft — injection system crash, the engine is not started up;
– absolute pressure (depression) in an inlet pipe — increase in fuel consumption, considerable deterioration in dynamics, a problem with launch of the engine;
– provisions of a butterfly valve — loss of power, breakthroughs and failures at dispersal, unstable work in the idling mode;
– temperatures of cooling liquid (it is established under the ignition coil) – difficulties with start-up in a frost: it is necessary to warm up the engine, supporting turns by an accelerator pedal, at an overheat power significantly decreases, the detonation appears;
– temperatures of the soaked-up air — increase in fuel consumption, increase in level of toxicity of the fulfilled gases;
– concentration of oxygen (lambda probe) – increase in fuel consumption, deceleration of power of the engine, unstable work idling. Damage of catalytic converter of the fulfilled gases is possible;
– speeds (it is established on a transmission case) – possibly deterioration in dynamic qualities of the car and increase in fuel consumption.

"previous page
3.1.4. Check of a power supply system of the engine
following page"
3.3. Idling was gone