Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
4.1. General provisions
4.2. Daily Service (DS)
4.3. First maintenance (TO-1)
4.3.1. Check and adjustment of a tension of a belt of the drive of the generator and pump of the hydraulic booster of steering
4.3.2. Check and adjustment of a tension of a belt of the drive of the compressor of the conditioner
4.3.3. Check of a belt of the drive of the gas-distributing mechanism
4.3.4. Replacement of oil in the engine and an oil filter
4.3.5. Cleaning of system of ventilation of a case
4.3.6. Check of hoses and connections of the cooling system
4.3.7. Check of system of production of the fulfilled gases
4.3.8. Check of tightness of fuel-supply lines
4.3.9. Replacement of the fuel filter
4.3.10. Replacement of the filtering element of the air filter
4.3.11. Check and adjustment of the drive of switching off of coupling
4.3.12. Check of level and a dolivka of oil in the transmission
4.3.13. Check of protective covers of drives of forward wheels
4.3.14. Check of technical condition of details of a forward suspension bracket on the car
4.3.15. Check of technical condition of details of a back suspension bracket on the car
4.3.16. Check and adjustment of angles of installation of wheels
4.3.17. Survey and check of steering on the car
4.3.18. Check of a free wheeling (side play) of a steering wheel
4.3.19. Check of tightness of a hydraulic actuator of brakes
4.3.20. Check of degree of wear of brake shoes, disks and drums
4.3.21. Check of operation of the vacuum amplifier of brakes
4.3.22. Check of overall performance of the brake system
4.3.23. Check of the parking brake
4.3.24. Service of the rechargeable battery
4.3.25. Replacement and service of spark plugs
4.3.26. Check and adjustment of light of headlights
4.3.27. Body fittings lubricant
4.3.28. Clearing of drainage openings
4.4. Second maintenance (TO-2)
5. Engine
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








4-3-4-zamena-masla-v-dvigatele-i-maslyanogo-filtra.html

4.3.4. Replacement of oil in the engine and an oil filter

According to the recommendation of manufacturer oil in the engine should be replaced in one year of operation or through 10 thousand km of a run depending on what will come earlier.

GOOD ADVICE
Under trying conditions operation in the large city or strongly dusty area replace oil and the filter through each 5000 km.

It will be required to you: engine oil, an oil filter, a pure rag, capacity for the merged oil with a capacity not less than 5 l, a key "on 19", a special key for an otvorachivaniye of an oil filter.

USEFUL TIPS
Merge oil after a trip until the engine cooled down yet. If the engine cold, launch and warm up it up to the working temperature.
Fill in oil of the same brand, as at oil which was in the engine. If all of you decided to replace oil brand, wash out the lubrication system flushing oil or oil of that brand which will be used. For this purpose after discharge of old oil fill in new to the lower tag of the masloizmeritelny probe. Launch the engine and let's it work 10 min. idling. Merge oil and only after that replace an oil filter. Now you can fill in new oil to the required level (to the top tag on the probe).

PREVENTION
Do not merge the fulfilled oil on the earth.

1. Clear a metal brush, and then a rag a stopper of a drain opening on an oil case of the engine. Turn off a stopper of a drain opening, previously having substituted capacity for the merged oil …
2. … also merge oil.

    
PREVENTION
Be careful: oil is hotter.

3. Wrap a stopper.

NOTE
The stopper is condensed with a copper washer. If the washer is pressed strongly out, surely replace it.

4. Shift from the place a special key an oil filter …

NOTE
The oil filter is established on a forward part of the block of cylinders of the engine around the 4th cylinder.

5. … also remove it.
6. Check purity and mobility of the antidrainage valve.

USEFUL TIPS
For an otvorachivaniye of an oil filter use a special key. If there is no such key or a similar stripper, punch the filter case the screw-driver and, using it as the lever, unscrew the filter. Punch the filter as it is possible closer to a bottom not to damage the union. It is possible to use also the strip of a rough emery paper curtailed twice, having wrapped up it the filter and having shifted it from the place hands.

7. If the sealing ring of the new filter is not processed by the manufacturer jellied lubricant or talc, oil a ring pure engine and wrap the filter on the place (hands without use of the tool) on 3/4 turns from the moment of contact of a ring and a flange of the block of cylinders.
8. Turn off a stopper of an oil-filling mouth …
9. … also remove it.
10. Fill in pure engine oil (see. "Check of level and dolivka of oil in the lubrication system"). Establish into place a stopper of an oil-filling mouth.
11. Launch the engine and let's it work idling several minutes (the alarm lamp of emergency pressure drop of oil has to go out through 2–3 from later launch of the engine). In operating time of the engine check whether there are no oil potek from under a stopper of a drain opening and an oil filter. Stop the engine, check oil level, if necessary add oil, tighten a stopper and the filter.

"previous page
4.3.3. Check of a belt of the drive of the gas-distributing mechanism
following page"
4.3.5. Cleaning of system of ventilation of a case