Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Check of a compression in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
5.6. Removal, installation and troubleshooting of a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. Head of the block of cylinders
5.9. Removal and installation of the engine
5.10. Repair of the engine
5.10.1. Dismantling of the engine
5.10.2. Troubleshooting of details of the engine
5.10.3. Assembly of the engine
5.11. Lubrication system
5.12. Cooling system
5.13. System of production of the fulfilled gases
5.14. Engine power supply system
5.15. System of catching of vapors of fuel
5.16. System of recirculation of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








5-10-3-sborka-dvigatelya.html

5.10.3. Assembly of the engine

It will be required to you: a dynamometer key, the hammer (it is desirable with brisk of soft metal or polyurethane), the device for installation of pistons in cylinders, the same keys, as for dismantling of the engine, the screw-driver, an assembly shovel.
1. Insert a rod into the piston, oil a piston finger engine and press it in a rod on the same adaptation on which the finger was pressed off, or by means of the hammer and the suitable mandrel inserted into an internal opening of a finger. The piston has to nestle a lug on the top head of a rod in the direction of a finger press fitting that will allow it to reach the correct position.

NOTE
The finger is implanted into the top head of a rod with a tightness therefore for simplification of assembly and preservation of its landing it is recommended to heat rods, having placed them the top heads for 15 min. in the electric furnace heated to 240 °C. Temperature of heating of a rod can be checked by means of a termokhromny pencil. For the correct connection of a finger with a rod press a finger as soon as possible as after its cooling position of a finger cannot be changed already.


Fig. 5.12. An order of an arrangement of piston rings on the piston: 1 – rod; 2 – piston; 3 – lower ring of a compound oil scraper ring; 4 – dilator of an oil scraper ring; 5 – top ring of a compound oil scraper ring; 6 – lower compression ring; 7 – top compression ring; 8 – tag

2. Establish piston rings as it should be, the return to removal, having arranged them, as shown in fig. 5.12.

PREVENTION
At installation do not unclench a ring more, than it is necessary not to deform or to break them.

NOTES
Establish the lower compression ring by bore down (it is shown by an arrow) in the second flute.
Marking of "Y" on compression rings has to be directed up.



Fig. 5.13. An arrangement of locks of piston rings before installation of the piston in the cylinder: 1 – dilator of an oil scraper ring and top compression ring; 2 – top ring of a compound oil scraper ring; 3 – lower compression ring; 4 – lower ring of a compound oil scraper ring

3. Orient rings, as shown in fig. 5.13. Install rings on other pistons.

NOTE
Locks of the top and lower rings of a compound oil scraper ring have to be located at distance of 25-30 mm respectively to the left and to the right from the dilator lock.

4. Lay the top inserts of radical bearings in a bed of the block of cylinders.

NOTES
The average (third) radical bearing put an insert of the increased thickness with basic fillets to bed.
Establish inserts so that the adjusting short mustache of an insert was combined with dredging on a bed.

5. Oil inserts engine.
6. Install a bent shaft in the block of cylinders.
7. Lay the lower inserts in covers of radical bearings, having combined short moustaches of inserts with dredging on covers.

NOTE
The top and lower inserts of radical bearings can differ on an opening arrangement for an oil supply. Establish inserts so that these openings coincided with openings of channels for an oil supply in beds of support of radical bearings. After installation of inserts in nests their ends come out a little therefore for the correct orientation of inserts at a final inhaling of bolts of fastening of covers of bearings track that the vystupaniye of both ends was identical.

8. Oil engine radical necks of a bent shaft.
9. Oil engine inserts in covers of radical bearings of a bent shaft.
10. Establish covers of radical bearings according to serial numbers, having oriented on tags.

PREVENTION
For installation of covers of bearings of a bent shaft use the hammer with soft brisk, made of brass, lead or polyurethane. It is forbidden to establish covers by an inhaling of fasteners as in this case landing surfaces of covers and the block of cylinders will be damaged.

11. Establish bolts of covers, evenly screw bolts down, without tightening finally, turn out on one turn, tighten the moment 50 N · m (5,0 kgfs · l) also tighten on 40-60 °.

PREVENTION
Surely replace bolts of fastening of covers of radical bearings new.

12. Check correctness of assembly, having turned a bent shaft a hand on several turns. The shaft has to rotate freely and smoothly.
13. Establish inserts in rods, having combined an adjusting short mustache of an insert with dredging on a rod.
14. Oil engine mirrors of cylinders, pistons, piston rings and connecting rods.
15. Install the device for compression of rings on the piston and, wrapping the screw, squeeze rings.
16. Turn a bent shaft so that his conrod neck on which mount conrod and piston group was established in VMT. Install the piston in the cylinder according to marking of number of the cylinder on a rod, press (for example, the hammer handle) the piston and shift it from a mandrel in the cylinder. Similarly install pistons in other cylinders.

NOTE
At installation of pistons the tag (triangle) on the piston has to be turned into cylinders to a forward part of the engine.

PREVENTION
Install the piston in the cylinder carefully not to injure the lower head of a rod a conrod neck of a bent shaft.

17. Establish connecting rods in covers of rods, having combined an adjusting short mustache of an insert with dredging on a cover.
18. Oil engine connecting rods in covers of rods and conrod necks of a bent shaft.
19. Establish a rod cover, having connected a rod to a neck of a bent shaft and having combined tags on a rod and a cover.
20. Screw conrod bolts, without tightening them it is final.
21. Tighten conrod bolts to the full, without tightening them it is final; then turn off them on one turn, tighten the moment 25 N · m (2,5 kgfs · l) also tighten for 30 °, and then for 15 °.
22. Check ease of movement of a rod along a conrod neck. When jamming turn off conrod bolts and repeatedly tighten them the nominal moment.
23. Check a side gap of a rod, it has to be 0,070–0,242 mm. The increased gap indicates excessive wear of cheeks of cranks of a bent shaft. In this case replace a bent shaft.
24. Similarly fix covers of other rods.
25. Check an axial gap of a bent shaft, it has to be 0,07–0,1 mm. The increased gap indicates wear of basic flanges of a bent shaft or bed of the average radical bearing. In this case replace a bent shaft. If it does not lead to reduction of an axial gap, it is necessary to replace the block of cylinders.
26. Establish a back epiploon of a bent shaft (see. "Replacement of epiploons of a bent shaft").
27. Establish an oil receiver and the oil pump (see. "Removal and installation of the oil pump").
28. Establish an oil case (see. "Replacement of consolidation of an oil case").
30. Further collect the engine as it should be, the return to dismantling. Installation of a head of the block of cylinders is described in the subsection "Replacement of Laying of a Head of the Block of Cylinders", the water pump — in the subsection "Replacement of the Water Pump", a belt of the drive of the gas-distributing mechanism — in the subsection "Replacement and Adjustment of a Tension of a Belt of the Drive of the Gas-distributing Mechanism and Replacement of Its Tension Roller".

GOOD ADVICE
After assembly of the engine it is recommended to carry out its running in at the stand. As out of the special repair organizations it is impossible to make it, after installation of the engine on the car roll it on the simplified cycle in the following order.
1. Be convinced of correctness of adjustment of the drive of a butterfly valve, fill in oil and cooling liquid, check tightness of all connections.
2. Launch the engine and let's it work without loading on the following cycle.
You do not bring operation of the engine to the maximum modes.
3. In operating time check tightness of the engine and its systems, oil pressure, pay attention to existence of extraneous noises.
4. If extraneous noises or other malfunctions are found, stop the engine and remove their cause.
5. Having begun operation of the car, observe the modes provided for the period of a running in of the new car.


"previous page
5.10.2. Troubleshooting of details of the engine
following page"
5.11. Lubrication system