Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Check of a compression in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
5.6. Removal, installation and troubleshooting of a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. Head of the block of cylinders
5.9. Removal and installation of the engine
5.10. Repair of the engine
5.11. Lubrication system
5.11.1. Features of a design
5.11.2. Removal and installation of the oil pump
5.11.3. Repair of the oil pump
5.12. Cooling system
5.13. System of production of the fulfilled gases
5.14. Engine power supply system
5.15. System of catching of vapors of fuel
5.16. System of recirculation of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








5-11-3-remont-maslyanogo-nasosa.html

5.11.3. Repair of the oil pump

Fig. 5.14. Details of the oil pump: 1 – stopper of the reducing valve; 2 – laying of a stopper; 3 – spring of the reducing valve; 4 – plunger; 5 – bolt of fastening of the oil pump; 6 – pump housing; 7 – adapter of the sensor of an alarm lamp of emergency pressure drop of oil; 8 – forward epiploon of a bent shaft; 9 – leading gear wheel; 10 – the conducted gear wheel; 11 – case cover; 12 – screw of fastening of a cover; 13 – laying of the case; 14 – safety valve; 15 – adjusting plug

The device of the oil pump is shown in fig. 5.14.

NOTE
The version of the oil pump shown in fig. 5.14 differs from version of the pump installed on the car used for shooting, an arrangement of reducing and safety valves a little. However all entering details are identical at all versions of pumps.

It will be required to you: keys "on 24", "on 27", a key hexagon "on 8", the screw-driver with a crosswise edge, a caliper, a set of flat probes.
1. Remove the oil pump from the car (see. "Removal and installation of the oil pump").

NOTE
If sealing laying remained on a pump housing and is not damaged, it can be not separated from the case. In this case at the return installation of the pump grease laying with a thin layer of sealant.

2. Merge oil from the pump.
3. Take out from boring of the case any pointed tool (for example, the screw-driver) a forward epiploon of a bent shaft.
4. Turn out from an adapter of the case of the oil pump the sensor of 1 alarm lamp of emergency pressure drop of oil (if it is established on the pump), and from a pump housing — the safety valve 2 and a stopper 3 reducing valves. Take from a case cavity a spring 3 (see fig. 5.14) and a plunger 4 reducing valves.

PREVENTION
The spring of the reducing valve is established with a tightness. In order to avoid getting injured turn out a stopper carefully.

NOTE
Pay attention: under a stopper of the reducing valve sealing laying is established, do not lose it.

5. Turn out five screws of fastening of a cover of the pump …
6. … also uncover.
7. Take the leader from a case cavity …
8. … and conducted pump gear wheels.
9. Wash out a pump housing and the dismantled details to remove dirt and deposits. Remove dense varnish deposits from internal cavities of the pump, previously having softened them solvent.

GOOD ADVICE
Varnish oil deposits well are removed the means which are available on sale for washing of the engine (so-called "five-minutes").

10. Examine the case and a cover of the pump. In the presence of cracks, scratches, defects of casting, the damaged carving openings replace the case (as it is not maintainable) or the pump assembled.
11. Check a plunger of the reducing valve for existence of scratches and traces of jamming. Small dents and agnails can be removed with grinding whetstone of small granularity.
12. Check a spring of the reducing valve for residual deformation and a bend. Spring length in a free state has to be 81 mm. Replace strongly pressed out or damaged spring.
13. Check gear wheels for existence of a vykrashivaniye of metal, the tease and wear of teeths. Replace the damaged gear wheels or gear wheels on which the increased unilateral wear of teeths is swept visually up.
14. Check an axial gap between end faces of gear wheels and the plane of a cover of the pump. It can be made in two next ways.
15. At the first way measure the leader's thickness …
16. … and conducted gear wheels …
17. … and also boring depth in the case under gear wheels. Calculate an axial gap as a difference of arithmetic-mean value of depth of boring and thickness of gear wheels.
18. At the second way of check install the conducted gear wheel in the case, put a metal ruler (or a caliper) an end face on the case and measure by the probe a gap between the case and a ruler.
19. Similarly measure an axial gap of the leading gear wheel.
20. The most admissible gaps measured in both ways have to be 0,045–0,100 mm for the conducted gear wheel and 0,035–0,085 mm for the leading gear wheel. If at least one of gaps does not correspond to the specified value, replace the case or the pump assembled.
21. Collect the pump in the sequence, the return dismantling. Before a press fitting in a pump cover oil a forward epiploon of a bent shaft engine. Apply on a carving of a stopper of the reducing valve an anaerobic clamp of a carving of Loctite 573 or similar to it and tighten a stopper the moment of 30 N · m (3,0 kgfs · м). If you establish new laying 13 (see fig. 5.14), paste it to the case jellied lubricant.

PREVENTIONS
Use only company factory laying. Installation of laying of other thickness will lead to violation of operation of the pump.
In order to avoid damage of the engine at the first start-up after installation of the oil pump before installing gear wheels in its case, fill all cavities of the pump with jellied mineral lubricant for ensuring absorption of oil from an oil case.
If at the first launch of the engine with the replaced oil pump oil pressure does not rise to demanded at once, immediately stop the engine, remove an oil case and check tightness of connection of the pump with an oil receiver. If necessary repeatedly disassemble the pump and again fill his cavities with jellied mineral lubricant. In the absence of necessary pressure in the lubrication system even short-term operation of the engine leads to its emergency damage.


"previous page
5.11.2. Removal and installation of the oil pump
following page"
5.12. Cooling system