Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Check of a compression in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
5.6. Removal, installation and troubleshooting of a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. Head of the block of cylinders
5.9. Removal and installation of the engine
5.10. Repair of the engine
5.11. Lubrication system
5.12. Cooling system
5.13. System of production of the fulfilled gases
5.14. Engine power supply system
5.14.1. Features of a design
5.14.2. Check of pressure in an engine power supply system
5.14.3. Pressure decrease in a power supply system
5.14.4. Removal and installation of the air filter, muffler of noise of an admission and air duct
5.14.5. Replacement of the fuel pump
5.14.6. Replacement of the fuel tank and its bulk pipe
5.14.7. Check and replacement of the regulator of pressure of fuel
5.14.8. Removal and installation of a fuel stage
5.14.9. Removal, installation and check of nozzles
5.14.10. Removal and installation of throttle knot
5.14.11. Check and replacement of the regulator of idling
5.14.12. Adjustment and replacement of a cable of the drive of a butterfly valve
5.14.13. Removal and installation of a pedal of an accelerator
5.15. System of catching of vapors of fuel
5.16. System of recirculation of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








5-14-12-regulirovka-i-zamena-trosa-privoda-drosselnojj-zaslonki.html

5.14.12. Adjustment and replacement of a cable of the drive of a butterfly valve

If adjustment of the drive of a butterfly valve it is impossible to achieve full opening or closing of a butterfly valve or the drive jams, replace a cable of the drive of a butterfly valve.
It will be required to you: screw-driver, passatizh.
1. For visual control of movement of a butterfly valve weaken a collar of fastening and disconnect the airbringing sleeve from a branch pipe of throttle knot (see. "Removal and installation of throttle knot").
2. At completely pressed accelerator pedal (it the assistant has to make) check the provision of a butterfly valve — it has to be completely open, and at the released accelerator pedal — is completely closed. Otherwise the drive needs to be adjusted.
3. Take a spring bracket from a cable cover tip cut and movement of a tip in an opening of a rubber damper achieve forward that the butterfly valve was completely closed. At not completely opening gate movement achieve back that the gate completely opened. Record a cable tip in new situation, having inserted a bracket into its corresponding cut.
    
NOTE
If the cable is adjusted correctly, the deflection from effort of a hand of its branch between a tip of a cover and the sector of throttle knot has to be no more than 10 mm.

4. If a cable it is greatest possible will pull movement of a tip of a cover in a damper, and the butterfly valve all the same completely does not open, increase a full speed of a pedal of an accelerator the persistent screw installed on a pedal under the dashboard. At a screw reversing from a pedal arm its course increases, at a vvorachivaniye — decreases.
5. For replacement of a cable take out a tip of a cable of the drive of a butterfly valve from a groove of the sector and disconnect a cable from throttle knot.
6. Bring a cable cover damper out of an arm cut.
7. In salon under the dashboard squeeze the screw-driver a collet clip of a tip of a cable, take it from an opening of a pedal and bring a cable out of a cut in a pedal.
8. Extend a cable in podkapotny space through an opening in a front board.
9. Establish a cable of the drive of a butterfly valve as it should be, the return to removal.
10. After installation adjust a cable tension (see subitem 1-4 of this subsection).

"previous page
5.14.11. Check and replacement of the regulator of idling
following page"
5.14.13. Removal and installation of a pedal of an accelerator