Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Check of a compression in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
5.6. Removal, installation and troubleshooting of a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. Head of the block of cylinders
5.9. Removal and installation of the engine
5.10. Repair of the engine
5.11. Lubrication system
5.12. Cooling system
5.13. System of production of the fulfilled gases
5.14. Engine power supply system
5.14.1. Features of a design
5.14.2. Check of pressure in an engine power supply system
5.14.3. Pressure decrease in a power supply system
5.14.4. Removal and installation of the air filter, muffler of noise of an admission and air duct
5.14.5. Replacement of the fuel pump
5.14.6. Replacement of the fuel tank and its bulk pipe
5.14.7. Check and replacement of the regulator of pressure of fuel
5.14.8. Removal and installation of a fuel stage
5.14.9. Removal, installation and check of nozzles
5.14.10. Removal and installation of throttle knot
5.14.11. Check and replacement of the regulator of idling
5.14.12. Adjustment and replacement of a cable of the drive of a butterfly valve
5.14.13. Removal and installation of a pedal of an accelerator
5.15. System of catching of vapors of fuel
5.16. System of recirculation of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








5-14-13-snyatie-i-ustanovka-pedali-akseleratora.html

5.14.13. Removal and installation of a pedal of an accelerator

The pedal of an accelerator is removed for replacement of plastic plugs of its axis at emergence of a scratch, jamming or the increased side play, and also for replacement of a returnable spring at its damage.

NOTE
Plugs of an axis of a pedal of an accelerator and its returnable spring can be replaced and directly on the car, but as access to a pedal is quite complicated, we recommend to remove a pedal assembled with an arm.

It will be required to you: a face key "on 12", the screw-driver.
1. Disconnect a cable of the drive of a butterfly valve from a pedal (see. "Adjustment and replacement of a cable of the drive of a butterfly valve").
2. Turn off two nuts of fastening of an arm of a pedal to a front board …
3. … also remove an accelerator pedal assembled with an arm.

Педаль акселератора
Fig. 5.26. Accelerator pedal: 1 – platform of a pedal; 2 – pedal core; 3 – pedal arm; 4 – washer; 5 – pedal axis; 6 – lock washer; 7 – plug; 8 – returnable spring

4. For replacement of two plastic plugs 7 (fig. 5.26) of an axis 5 pedals remove lock washers 6 from both ends of an axis, having hooked them the screw-driver. Then take an axis 5 of openings of an arm 3, serially removing from it the plastic plug 7, a steel washer 4 and a returnable spring 8. Remove the second steel washer and the plastic plug from an axis.
    
NOTE
So details of fastening of a pedal of an accelerator look. In the photo they are located in the same order in which are installed on the car.

5. Collect a pedal of an accelerator and install it on the car as it should be, the return to dismantling and removal.

"previous page
5.14.12. Adjustment and replacement of a cable of the drive of a butterfly valve
following page"
5.15. System of catching of vapors of fuel