Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Check of a compression in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
5.6. Removal, installation and troubleshooting of a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. Head of the block of cylinders
5.9. Removal and installation of the engine
5.10. Repair of the engine
5.11. Lubrication system
5.12. Cooling system
5.13. System of production of the fulfilled gases
5.14. Engine power supply system
5.14.1. Features of a design
5.14.2. Check of pressure in an engine power supply system
5.14.3. Pressure decrease in a power supply system
5.14.4. Removal and installation of the air filter, muffler of noise of an admission and air duct
5.14.5. Replacement of the fuel pump
5.14.6. Replacement of the fuel tank and its bulk pipe
5.14.7. Check and replacement of the regulator of pressure of fuel
5.14.8. Removal and installation of a fuel stage
5.14.9. Removal, installation and check of nozzles
5.14.10. Removal and installation of throttle knot
5.14.11. Check and replacement of the regulator of idling
5.14.12. Adjustment and replacement of a cable of the drive of a butterfly valve
5.14.13. Removal and installation of a pedal of an accelerator
5.15. System of catching of vapors of fuel
5.16. System of recirculation of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








5-14-4-snyatie-i-ustanovka-vozdushnogo-filtra-glushitelya-shuma-vpuska-i-vozdukhovoda.html

5.14.4. Removal and installation of the air filter, muffler of noise of an admission and air duct

The air filter is removed at its damage and for receiving access to other units in a motor compartment.
It will be required to you: a key "on 10" (it is more convenient face), the screw-driver with a crosswise edge.
For removal of the air filter execute the following.
1. Weaken a fastening collar to the air filter of the airbringing sleeve …
2. … also disconnect a sleeve from a filter branch pipe.

NOTE
Pay attention that on a branch pipe of the air filter and on the edge of the airbringing sleeve there are triangular tags for the correct installation of a sleeve. Attaching a sleeve to the air filter, combine these tags.

3. Turn out three bolts of fastening of the air filter to a mudguard …
4. … also remove the air filter, having taken out the branch pipe located in the filter case bottom from a mouth of an air duct of the muffler of noise of an admission.
5. Install the air filter as it should be, the return to removal.

For removal of the muffler of noise of an admission and an air duct execute the following.
1. Remove the right forward wheel and establish a forward part of the car on a reliable support.
2. Remove the flap of the right forward wing (see. "Removal and installation of mudguards of wheels and flaps").
3. Turn out a bolt of fastening of an arm of the muffler of noise of an admission to a body.
4. Take the holder of the muffler from an arm opening on a body …
5. … also remove the muffler, shifting it from an air duct branch pipe.
6. Take the holder of the bringing air duct sleeve from an opening in a body …
7. … also remove an air duct, taking a sealant of its taking-away sleeve from an opening in a body.
8. Establish details as it should be, the return to removal.

"previous page
5.14.3. Pressure decrease in a power supply system
following page"
5.14.5. Replacement of the fuel pump