Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Check of a compression in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
5.6. Removal, installation and troubleshooting of a flywheel
5.7. Replacement of details of consolidation of the engine
5.7.1. Replacement of laying of a cover of a head of the block of cylinders
5.7.2. Replacement of laying of a head of the block of cylinders
5.7.3. Replacement of oil scraper caps
5.7.4. Replacement of an epiploon of the camshaft
5.7.5. Replacement of epiploons of a bent shaft
5.7.6. Replacement of consolidation of an oil case
5.7.7. Replacement of laying of an inlet pipe
5.7.8. Replacement of laying of a final collector
5.8. Head of the block of cylinders
5.9. Removal and installation of the engine
5.10. Repair of the engine
5.11. Lubrication system
5.12. Cooling system
5.13. System of production of the fulfilled gases
5.14. Engine power supply system
5.15. System of catching of vapors of fuel
5.16. System of recirculation of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








5-7-6-zamena-uplotneniya-maslyanogo-kartera.html

5.7.6. Replacement of consolidation of an oil case

The oil case is established on sealant, any laying in consolidation is absent therefore in case of an oil leak tightening of bolts of fastening of a case will not result in desirable result. It is necessary to remove an oil case and again to establish it on sealant.
Perform work on a viewing ditch, a platform or whenever possible on the elevator.
It will be required to you: a face head "on 10", a key "on 14" (it is desirable cap).
1. Merge oil from the engine (see. "Replacement of oil in the engine and an oil filter").
2. Turn off nuts of fastening of a flange of a reception pipe to a final collector (see. "Replacement of a reception pipe") also remove a flange from hairpins.
3. Turn out two bolts forward …
4. … bolt of back …
5. … and a bolt of an average of fastenings of a case of the transmission to an oil case.
6. Turn out two bolts of fastening of an oil case located in wells in its back part …
7. … and thirteen bolts located outside.
8. Separate an oil case from the block of cylinders the screw-driver inserted into a gap between a case and an arm of the block …
9. … also remove a case, having wrung out a reception pipe down.
10. Remove old sealant from the privalochny surfaces of the block of cylinders …
11. … and oil case. Carefully wipe rags oil from privalochny surfaces.

GOOD ADVICE
Do not degrease the Privalochny surfaces of the block and a case before putting sealant, only carefully remove from them oil. Further it will provide a possibility of easy dismantling of connection.

12. Apply sealant on privalochny surfaces and a carving part of bolts of fastening of an oil case.
13. Establish an oil case and evenly cross-wise tighten bolts the moment specified in the appendix 1.
14. Establish all removed details and knots as it should be, the return to removal.
15. Fill in oil in the engine.

PREVENTION
It is possible to launch the engine after replacement of consolidation of an oil case not earlier than in one hour, it is necessary for sealant polymerization.

"previous page
5.7.5. Replacement of epiploons of a bent shaft
following page"
5.7.7. Replacement of laying of an inlet pipe