Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Check of a compression in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
5.6. Removal, installation and troubleshooting of a flywheel
5.7. Replacement of details of consolidation of the engine
5.7.1. Replacement of laying of a cover of a head of the block of cylinders
5.7.2. Replacement of laying of a head of the block of cylinders
5.7.3. Replacement of oil scraper caps
5.7.4. Replacement of an epiploon of the camshaft
5.7.5. Replacement of epiploons of a bent shaft
5.7.6. Replacement of consolidation of an oil case
5.7.7. Replacement of laying of an inlet pipe
5.7.8. Replacement of laying of a final collector
5.8. Head of the block of cylinders
5.9. Removal and installation of the engine
5.10. Repair of the engine
5.11. Lubrication system
5.12. Cooling system
5.13. System of production of the fulfilled gases
5.14. Engine power supply system
5.15. System of catching of vapors of fuel
5.16. System of recirculation of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








5-7-7-zamena-prokladki-vpusknojj-truby.html

5.7.7. Replacement of laying of an inlet pipe

Between flanges of a head of the block of cylinders and an inlet pipe the sealing laying made of the pressed asbestos leaf reinforced by steel is established. At violation of tightness of this laying the engine works unevenly ("troit"). If it is not possible to eliminate malfunction with tightening of fastening of an inlet pipe, replace laying.
For replacement of laying of an inlet pipe it is not required to disconnect any hoses (except a hose of system of ventilation of a case of the engine) and wires. Their flexibility allows to take away an inlet pipe from a head of the block of cylinders on the distance sufficient for laying removal.
You will need a face or cap key "on 12".
1. Merge liquid from the cooling system (see. "Replacement of cooling liquid").
2. Weaken a tension of a belt of the drive of the generator and pump of the hydraulic booster of steering and take off a belt from a generator pulley (see. "Replacement of a belt of the drive of the generator and pump of the hydraulic booster of steering").

Fig. 5.5. Sequence of an otvorachivaniye of nuts and bolts of fastening of an inlet pipe

3. Turn out a bolt of fastening of a tension level of the generator and take away the generator from the engine, having turned it on an arm.
4. Weaken a collar of fastening of a hose of system of ventilation of a case of the engine to a branch pipe of a cover of a head of the block of cylinders, having squeezed passatizham its unbent ears, shift a collar on a hose …
5. … also disconnect a hose from a cover.
6. Turn off ten nuts and bolts of fastening of an inlet pipe in the sequence shown in fig. 5.5.
7. Remove an inlet pipe from hairpins, take slightly aside and remove laying from hairpins.
8. Carefully clear privalochny surfaces of a head of the block and an inlet pipe of the remains of old laying.
9. Establish new laying and all removed details in the sequence, the return to removal.
10. Tighten bolts and nuts of fastening of an inlet pipe in the sequence, return shown in fig. 5.5, the moment given in the appendix 1.

    
GOOD ADVICE
In order to avoid sticking of laying and for increase in its tightness we recommend to grease before installation of laying it on both sides a thin layer of graphitic lubricant.
Grease hairpins of a head of the block of cylinders and bolts of fastening of an inlet pipe with graphitic lubricant.


"previous page
5.7.6. Replacement of consolidation of an oil case
following page"
5.7.8. Replacement of laying of a final collector