Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Check of a compression in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
5.6. Removal, installation and troubleshooting of a flywheel
5.7. Replacement of details of consolidation of the engine
5.7.1. Replacement of laying of a cover of a head of the block of cylinders
5.7.2. Replacement of laying of a head of the block of cylinders
5.7.3. Replacement of oil scraper caps
5.7.4. Replacement of an epiploon of the camshaft
5.7.5. Replacement of epiploons of a bent shaft
5.7.6. Replacement of consolidation of an oil case
5.7.7. Replacement of laying of an inlet pipe
5.7.8. Replacement of laying of a final collector
5.8. Head of the block of cylinders
5.9. Removal and installation of the engine
5.10. Repair of the engine
5.11. Lubrication system
5.12. Cooling system
5.13. System of production of the fulfilled gases
5.14. Engine power supply system
5.15. System of catching of vapors of fuel
5.16. System of recirculation of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








5-7-8-zamena-prokladki-vypusknogo-kollektora.html

5.7.8. Replacement of laying of a final collector

Between flanges of a head of the block of cylinders and a final collector the sealing laying made of the pressed asbestos leaf reinforced by steel is established. At violation of tightness of this laying there is a break outside of the fulfilled gases which is followed by a characteristic sharp sound (the collector "secht"). If it is not possible to eliminate malfunction with tightening of fastening of a final collector, replace laying.
You will need a face head "on 12".

NOTE
When replacing laying of a final collector it is possible not to disconnect a flange of a reception pipe from a collector. There is enough, having turned off nuts of fastening of a collector, to remove it from hairpins of a head of the block and to take away from a head so as far as flexibility of system of release allows. Through the formed gap it is possible to take out laying of a collector.

Последовательность отворачивания гаек крепления выпускного коллектора
Fig. 5.6. Sequence of an otvorachivaniye of nuts of fastening of a final collector


1. Remove the thermoscreen of a final collector (see. "Removal and installation of thermoscreens").
2. Turn off eight nuts of fastening of a final collector in the sequence shown in fig. 5.6.
3. Remove a final collector from hairpins …
4. … and the laying established under it.
5. Carefully clear privalochny surfaces of a head of the block and a final collector of the remains of old laying and a deposit.
6. Establish new laying and all removed details in the sequence, the return to removal.
7. Tighten nuts of fastening of a final collector in the sequence, return shown in fig. 5.6, the moment given in the appendix 1.

GOOD ADVICE
In order to avoid burning of laying and for increase in its tightness we recommend to grease before installation of laying it on both sides a thin layer of graphitic lubricant.
Grease hairpins of a head of the block of cylinders with graphitic lubricant.


"previous page
5.7.7. Replacement of laying of an inlet pipe
following page"
5.8. Head of the block of cylinders