Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
7.1. Forward suspension bracket
7.1.1. Features of a design
7.1.2. Possible malfunctions of a forward suspension bracket, their reason and ways of elimination
7.1.3. Removal and installation of a damping rack
7.1.4. Repair of a damping rack
7.1.5. Replacement of the top support of a damping rack
7.1.6. Replacement of a spherical support of a damping rack
7.1.7. Replacement of the lever of a forward suspension bracket
7.1.8. Replacement of details of the stabilizer of cross stability of a forward suspension bracket
7.1.9. Replacement of the bearing of a forward nave
7.2. Back suspension bracket
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








7-1-8-zamena-detalejj-stabilizatora-poperechnojj-ustojjchivosti-perednejj-podveski.html

7.1.8. Replacement of details of the stabilizer of cross stability of a forward suspension bracket

It will be required to you: keys "on 10", "on 12", face heads "on 12", "on 14", a neck, the extender, the cardan hinge.
1. You will hang out a forward part of the car and remove engine mudguards (see. "Removal and installation of mudguards of the engine").
2. Turn off a nut of fastening of a rack of the stabilizer of cross resistance to a bar, holding a bolt a face head and a neck.
3. Remove the top washer …
4. … and rubber plug. If you remove a rack not for replacement, mark an arrangement of other details of a rack before removal to establish them on former places.
5. Putting forward a bolt down, remove washers, rubber plugs and the expansion plug of a rack of the stabilizer of cross stability.
6. Similarly remove the second rack of the stabilizer.
7. Turn out two bolts of fastening of the right bracket …
8. … also remove a bracket of fastening of a bar of the stabilizer …
9. … and rubber plug.
10. Turn out two bolts of the left bracket of fastening of a bar of the stabilizer.

    
NOTE
For a reversing of bolts of fastening of the left bracket use the extender and the cardan hinge.

11. Remove a bracket of fastening of a bar of the stabilizer and the rubber plug.
    
NOTE
Replace the damaged or worn-out plugs new.

12. Turn out bolts of fastening of the first …
13. … and movement of the car of holders of tubes, the second for the direction.
14. Remove a stabilizer bar from the car. Do not unbend a tube more, than it is necessary for removal of a bar of the stabilizer not to damage them.

Стойка стабилизатора
Fig. 7.3. Stabilizer rack: 1, 6, 11, 12 – washers; 2 – nut; 3 – bolt; 4, 8, 9, 13 – rubber plugs; 5 – stabilizer bar; 7 – expansion plug; 10 – lower lever; In – the assembly size

15. Establish details as it should be, the return to removal. The relative positioning of details of a rack is shown in fig. 7.3. Pay attention to a relative positioning and orientation of washers and plugs, ledges of plugs have to enter openings of the lever and a bar so that the bolt of a rack did not concern the lever and a bar. Finally tighten nuts 2 (see fig. 7.3) before obtaining the size B equal to 38 mm, on the car standing on the earth.

NOTE
After replacement of details of the stabilizer of cross stability check and if necessary adjust the angles of installation of wheels. Use services of the workshops having the special equipment.

"previous page
7.1.7. Replacement of the lever of a forward suspension bracket
following page"
7.1.9. Replacement of the bearing of a forward nave