Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
6. Transmission
7. Running gear
7.1. Forward suspension bracket
7.2. Back suspension bracket
7.2.1. Features of a design
7.2.2. Possible malfunctions of a back suspension bracket, their reason and ways of elimination
7.2.3. Replacement of the shock-absorber of a back suspension bracket
7.2.4. Replacement of a spring of a back suspension bracket
7.2.5. Replacement of saylentblok of levers of a back suspension bracket
7.2.6. Adjustment of bearings of a back nave
7.2.7. Replacement of bearings of a back nave
7.2.8. Replacement of a beam of a back suspension bracket
7.2.9. Replacement of the stabilizer of cross stability of a back suspension bracket
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








7-2-7-zamena-podshipnikov-zadnejj-stupicy.html

7.2.7. Replacement of bearings of a back nave

It will be required to you: a face head "on 24", flat-nose pliers, the screw-driver with a flat edge, small beards, a stripper for a bearing vypressovka, a universal stripper.
1. Weaken an inhaling of bolts of fastening of a wheel.
2. Include the I transfer and establish an emphasis under forward wheels. Raise and establish a back part of the car on reliable support.
3. Remove the corresponding wheel.
4. Remove the brake drum (see. "Removal and installation of the brake drum"). Also the internal ring of the external bearing, both rings of the internal bearing and an epiploon will be at the same time removed.
5. Take an epiploon, having hooked it the screw-driver.
    
GOOD ADVICE
Replace an epiploon new at each removal.

6. Take out an internal ring of the internal bearing from a nave.
7. Using the hammer and small beards, beat out and take out an external ring of the external bearing from a nave.
    
NOTE
For a vypressovka in the case of a nave of the brake drum two grooves are executed (on a photo one is visible, the second is located diametrically).

8. Similar to a vypressuyta an external ring of the internal bearing.
    
NOTE
For a vypressovka in the case of a nave of the brake drum two grooves are executed (on a photo one is visible, the second is located diametrically).

9. Clear an internal cavity of a nave and a pin of old lubricant. On landing surfaces under bearings on a pin and a nave there should not be wear tracks, chips, забоин, zadir. With the specified defects replace the damaged details.
10. Grease an internal cavity of a nave and a pin with lubricant for Litol-24 bearings or its import analog (Hytex EP-2 of Texaco, Mobilux 2, 3, EP2, EP3, Mobilgrease MP of Mobil, Energrease L2, LS3 of British Petroleum, etc.).
11. Press in a nave an external ring of the internal bearing a mandrel of suitable diameter.
12. Put lubricant in a nave cavity.
13. Similarly press an external ring of the new external bearing in a nave.
14. Establish previously greased internal ring of the internal bearing in a nave …
15. … also press an epiploon.

NOTE
Before installation of an epiploon grease its working edge with jellied lubricant.

16. Install the brake drum on a pin.
17. Establish an internal ring of the external bearing.
18. Establish a washer and a nut of a nave.
19. Establish a wheel.
20. Adjust bearings (see. "Adjustment of bearings of a back nave").

"previous page
7.2.6. Adjustment of bearings of a back nave
following page"
7.2.8. Replacement of a beam of a back suspension bracket