Chevrolet Lanos (since 2004 release)
1. Car device
2. Recommendations about operation
3. Malfunctions in way
4. Maintenance
5. Engine
5.1. Features of a design
5.2. Check of a compression in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression
5.6. Removal, installation and troubleshooting of a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. Head of the block of cylinders
5.9. Removal and installation of the engine
5.10. Repair of the engine
5.11. Lubrication system
5.12. Cooling system
5.13. System of production of the fulfilled gases
5.14. Engine power supply system
5.15. System of catching of vapors of fuel
5.16. System of recirculation of the fulfilled gases
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Wheels and tires
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Advice to the beginning mechanic
18. Appendices
19. Schemes of electric equipment
 








5-4-zamena-opor-podveski-silovogo-agregata.html

5.4. Replacement of support of a suspension bracket of the power unit

The power unit is installed on two support with rubber pillows on the right and at the left and one support (too with a rubber pillow) fixed through an arm on a transmission case.
It will be required to you: a face head "on 14", keys "on 17", "on 19", a jack or the similar load-lifting mechanism.
1. You will hang out a forward part of the car on support or lift the car on the elevator.
2. Remove the right mudguard of the engine (see. "Removal and installation of mudguards of the engine").

NOTE
For replacement of the right support of a suspension bracket of the power unit it is enough to remove only the right mudguard. For replacement of the left forward and back support mudguards do not need to be removed.

3. Establish a jack or a support under an engine case.
4. For replacement of a back support of a suspension bracket of the power unit turn off a nut of a bolt of fastening of a support to an arm on the transmission...
5. … also turn out two bolts of fastening of a support to a body.

NOTE
The forward bolt of fastening of a support is turned out through an opening in an arm.

6. Lower a support under the engine so that the support of a suspension bracket of the power unit was released, then take out a bolt of fastening of a support and remove it.
7. Establish a back support of a suspension bracket of the power unit as it should be, the return to removal, having oriented at installation so that the arrow applied on its external surface was directed in the direction of the movement of the car forward.

NOTE
Back and left support of a suspension bracket of the power unit of almost identical form also differ only with quantity of openings in an internal holder therefore pay attention to marking of a support. Get a new support with the same designation.

8. For replacement of the left support of a suspension bracket of the power unit turn out two bolts of fastening of a support to an arm …
9. … and to a body longeron …
10. … also remove a support.

NOTE
Pay attention to marking of a support. Get a new support with the same designation.

11. Establish the left support of a suspension bracket of the power unit as it should be, the return to removal.
12. Before replacement of the right support of a suspension bracket of the power unit take off a conditioner compressor drive belt (see. "Replacement of a belt of the drive of the compressor of the conditioner"), as it complicates access to a pillow.
13. Turn off two nuts of fastening of the right support to a body arm …
14. … turn out two bolts of fastening of a support to an engine arm …
15. … also remove a support.
16. Establish the right support of a suspension bracket of the power unit and all removed details as it should be, the return to removal.

"previous page
5.3. Removal and installation of mudguards of the engine
following page"
5.5. Installation of the piston of the first cylinder in the provision of VMT of a step of compression